Canine agility courses are made up of several different obstacles, designed to test dogs on their athletic abilities and training. An A-frame obstacle can be made with basic woodworking tools and materials. It should be lightweight -- so it can be moved without difficulty -- but strong enough to support the weight of your dog. A practice A-frame can be smaller than the American Kennel Club (AKC) regulation size of 35 to 49 inches wide, and within 2 inches of 9 feet, for each panel.
Instructions
- 1
Make two frames 3 feet wide by 8 feet long, with boards 1-inch thick by 4 inches wide, using 2-inch wood screws.
2Cut the ends of the boards at a 45 degree angle, so the bottom ends will rest flat on the ground, and the top ends will meet when the A-frame is set up.
3Place a board with the short edge down -- to form each side of the frame -- with a third board running up the middle.
4Attach four of the same boards, cut to size, horizontally at intervals between the 8-foot vertical boards for stability. Do not put these boards at either end of the frames.
5Attach a -inch by 3-foot by 8-foot sheet of exterior grade plywood to each of the frames with 2-inch wood screws.
6Round two edges of wooden slats -inch thick by up to 1.5 inches wide and approximately 36 inches long. The rounded edges should be on the same side of the wide part of each slat.
7Attach the slats -- rounded edges up -- to the top side of the plywood with 1-inch wood screws or wood glue to provide footing for your dog. "...Some people think that it can be crucial to get dog training tips earlier to getting their pets. Lots of people could find this fascinating but a lot of people could recognize that this is a great tip to follow. The challenge with a number of pet owners is they will get a dog and then find out that they are not suitable to take care of them. Finally, they could give up their pets in order to retrieve their previous lives. These dog training tips can let people find out what they have got to handle and if they have the time to educate their dogs. These hints will be found on Secrets To Dog Training. By using the time to conduct suitable dog training, you will get pleasure from a lifetime of comfortable companionship with your ".... The centers of the slats should be spaced 10 to 12 inches apart -- and the ends should be within inch of the plywood's edge. The bottom slat should be 42 to 46 inches from the bottom of each panel.
8Paint all of the wood with non-glossy, exterior paint. The contact zones, which are the bottom 42 inches of each panel, should be painted a contrasting color from the rest of the obstacle. The AKC rules state that white, black and brown cannot be used, and that bright yellow is recommended.
9Remove the pins from six door hinges. Insert a -inch steel rod -- approximately 35 inches long -- through all six of the hinges.
10Cut one of the long edges of four 1- by 6-inch boards -- that are two inches longer than three hinges laid side-by-side -- at a 45 degree angle.
11Screw one end of a set of three hinges to one of the boards with 1-inch wood screws -- so just the hinged part sticks out from the board. The hinges should be attached to the face opposite the 45 degree angle cut -- so that the hinges and the angle cut are along the same edge.
Do the same with the other end of the hinges, and a second board. Repeat the process with the remaining hinges and boards.
12Align the angled edge of each board to the front edge of the underside of the plywood, with one board near the outer edge of each panel. The hinges should be between the boards and the plywood. Screw through the top of the plywood into the boards with 1 1/4-inch wood screws, taking care to avoid the hinges. You should now be able to swing the panels open and shut with the aid of the hinges.
13Screw a hook bolt into the bottom of the outside board of each panel -- approximately one third of the way down from the top of the panels. Attach a chain that will stabilize the frame when it's set up. It should be stretched tight when the obstacle is fully extended.
How to Build Your Own Dog Agility Equipment eHow
www.ehow.com Pets Dogs Dog SuppliesAgility courses are often used in dog competitions to show off a dog's ability to run a set obstacle course. There are a number of obstacles, including a tunnel, a ...
How to Build a Dog Agility Course: Step-by-Step Instructions
www.wikihow.com Pets and Animals Dogs Working with DogsHow to Build a Dog Agility Course. Dog Agility is a growing sport in which a handler guides their dog through numerous obstacles such as jumps, weaves, and tunnels.
How to Build Your Own A-Frame Agility Equipment eHow
www.ehow.com Pets Dogs Relating to DogsOf all the standard pieces of agility equipment, the A-frame is one of the more difficult to build on your own. With effort and care, however, you can build a ...
Dog Agility Jump - Instructables - Make, How To, and DIY
www.instructables.com/id/Dog-Agility-JumpHello Everyone! My little Cockapoo, Ruby, loves to do Agility and I want to be able to practice with her at home! One of the first pieces of equipe...
DIY Dog Agility A-Frame - Instructables - Make, How To, and DIY
www.instructables.com/id/DIY-Dog-Agility-A-FrameWith A-Frames ranging from $500 bucks to $1,000 or more I figured I would save some cash, have some fun, and build my dog an Agility A-Frame to practi...
How to Build a Simple A-Frame Doghouse : How-To : DIY Network
www.diynetwork.com/how-to/how-to-build-a-simple-a-frame-doghouseDIY Network has step-by-step instructions for how to build a classic doghouse.
How to Build a Dog Kennel Complex, Dog House, a Whelping
www.lowchensaustralia.com/diy/kennels.htmShowing our little lion dogs off to the rest of the world!
How to Make: Dog Agility Jump! - YouTube
www.youtube.com/watch?v=xuJZTRytCmQThis is my plans on how to make one of the best practice quality dog agility jumps. All of the pictures and videos are owned by me. If you have any ...
How to Make Dog Agility Jumps for Practice - Build your Own ...
www.youtube.com/watch?v=XPsMxK1-LzUPlease Subscribe http://dft.ba/-sub Sub our Vlog Channel http://dft.ba/-2ndchannel Materials List: 2 10 foot PVC Poles, 1 inch in Diameter 6 End caps 2 PVC ...
How to Build an Adjustable Dog Agility Seesaw: 18 Steps
www.wikihow.com Pets and Animals Dogs Dog AccessoriesHow to Build an Adjustable Dog Agility Seesaw. This won't be USDAA or AKC approved, but it will be super for training, and will seem like the real thing to you and ...
Need clarification !) Step one is make frame and Step 2 is cut angles. Wouldn't you cut angles first and then begin frame? I count a total of 4 boards of the 1 x 4 x 8 for each panel ( 3 vertical and 1 for blocking). Thats a total of 8 boards of 1 x 4 x 8 so why does it say you need 10 or 11 boards?
ReplyDelete